УДК 661.185+622.279.7
(UDK 661.185+622.279.7)
(APPLICABILITY OF TECHNOLOGY FOR KILLING GAS AND GAS-CONDENSATE WELLS WITH FOAM COMPOSITIONS IN ROSNEFT FIELDS)
В статье проанализированы возможности применения жидкостей глушения скважин на зрелых месторождениях при проведении геолого-технических мероприятий. Дана оценка влияния различных технологий глушения скважин на фильтрационно-емкостные свойства пласта. Отмечено, что для снижения кольматации призабойной зоны пласта на объектах с пластовым давлением ниже гидростатического рекомендовано применение трехфазной пены в качестве жидкости глушения. Эффективность данной технологии обусловлена тем, что использование пенных составов предполагает снижение репрессии на продуктивный пласт в сравнении с глушением соляными и глинистыми растворами за счет регулирования плотности и структурно-механических свойств пен.
Проведен анализ текущих конструкций скважин в целях определения их средних технических характеристик, представлены данные о продуктивности скважин ряда месторождений Краснодарского края и Крайнего Севера до и после проведения капитального ремонта.
Произведен подбор характеристик пены и пенообразующей жидкости на основе текущих геолого-технических характеристик газовых и газоконденсатных скважин для минимизации риска поглощения жидкости глушения путем использования технологии глушения скважин пенными составами.
The article analyses the possibilities of well killing fluids application in mature fields during geological and technical measures. The influence of different well killing technologies on filtration-volumetric properties of the formation is evaluated. It has been noted that three-phase foam as a killing fluid has been recommended to reduce downhole zone clogging on the objects with formation pressure below hydrostatic pressure. The efficiency of this technology is stipulated by the fact that the use of foam makes it possible to decrease the repression on the payout bed in comparison with the killing with brine and clay solutions owing to the density and structural-mechanical properties of the foam.
Current well designs have been analyzed in order to determine their average performance characteristics and data on productivity of wells at a number of fields in the Krasnodar region and the Far North before and after workover have been presented.
A selection of foam and foaming fluid characteristics based on the current geological and technical characteristics of gas and gas condensate wells has been made to minimise the risk of killing fluid absorption by using the foam-killing technology.
Ivanova E.V., Afanasyev S.V. Development of a Method for Producing Oil Well Killing Fluid Based on Waste Water of Togliattiazot PJSC. In: Proceedings of the II All-Russian Scientific and Practical Conference “Innovations and “Green’ Technologies”. 2019. P. 84-89. (In Russ.)
Kunakova A.M., Olekhnovich R.O., Klim O.V. et al. Liquids for Killing Oil Wells. St. Petersburg: ITMO University; 2020. (In Russ.)
Amanov M.A., Ishangulyev G.A. Application of Light Technological Fluids for Killing and Workover of Wells in Conditions of Abnormally Low Formation Pressure (ALFP). Molodoi uchenyi [Young Scientist]. 2016;10(114):117–123. (In Russ.)
Foam-Forming Composition for Killing Of Wells: patent No. RU2208036C2; IPC C09 K7/08, E21 B43/12. Authors – R.A.-O. Gasumov, O.K. Tagirov, R.N. Kallaeva et al; patent holder – North Caucasus Natural Gas Research Institute OJSC of the Gazprom OJSC; No. 2001125656/03, appl. 18.09.2001; publ. 10.07.2003.
Geikhman M.G. Development and Perfection of Technologies of Repair of Gas Wells in the Conditions of the Lowered Formation Pressures and Intensive Watering of Deposits. Synopsis of Thesis for the degree of Candidate of Engineering Sciences. Tyumen: Tyumen State Oil-Gas University; 2005. (In Russ.)
Basarygin Y.M., Makarenko P.P., Mavromati V.D. Repair of Gas Wells. Moscow: Nedra; 1998. (In Russ.)